Installation Considerations for your CID1 Extraction Room and CID2 Fume Hood

Installation Considerations for your CID1 Extraction Room and CID2 Fume Hood

Installation the HAL Extraction Booth and Fume Hood to ensure a safe and compliant CID1 or CID2 space

Installation and assembly of your CID1 HAL Extraction Booth for hydrocarbon and Class IB solvent extraction and your CID2 HAL Extraction Fume Hood for primary or post-extraction processing, is simple and straight-forward. They are both designed to fit into most spaces and get your extraction process up and running as quickly as possible.

SETTING UP YOUR C1D1 EXTRACTION BOOTH

HAL Extraction Booth Systems are shipped for easy on-site construction. You will need a forklift to unload the crate upon delivery. The largest panels measure 40″ x 120″ x 3″. If you can get that panel into your space, you should be able to set up an Extraction Booth System.

A crew of two or three can assemble a small Extraction Booth in 12-16 hours, ready for connection to mechanical and electrical systems. There is no need for large overhead freight doors or demolition to get the system in place. Assembly time may vary based on the size unit purchased.

All HAL Extraction Booths are powered by a 208VAC 1PH circuit.

The Class I, Division 1 Extraction Booth must be assembled a minimum of 3 ft from all walls, unless those walls have a 1-hour fire-rating.

All exhaust ducting must be vented outside. Supply air can be ducted from outside, or the surrounding space, as long as the space can provide adequate air-flow. The exhaust cannot be recycled back into the supply side ventilation.

SETTING UP YOUR C1D2 EXTRACTION FUME HOOD

HAL Extraction Fume Hood Systems are shipped for easy on-site construction. You will need a forklift to unload the crate upon delivery. The largest panels measure 40″ x 120″ x 3″. If you can get that panel into your space, you should be able to set up an Extraction Fume Hood System.

A crew of two or three can assemble a small Fume Hood in 12-16 hours, ready for connection to mechanical and electrical systems. There is no need for large overhead freight doors or demolition to get the system in place. Assembly time may vary based on the size unit purchased.

All HAL Extraction Fume Hoods are powered by a 208VAC 1PH circuit.

The Class I, Division 2 Fume Hood must be assembled a minimum of 3 ft from all walls, unless those walls have a 1-hour fire-rating.

All exhaust ducting must be vented outside. Supply air is provided by the surrounding space, as long as the space can provide adequate air-flow.

CLASS I, DIVISION 1 EXTRACTION BOOTH PLACEMENT

The Extraction Booth System is assembled from the exterior, so space for the worker is required between the exterior wall of the Extraction Booth System and walls of the building.

The Extraction Booth shall be installed a minimum distance of 3 feet from all operations. The Extraction Booth can be installed within 3 feet from all operations if it is separated by a partition, wall, or floor/ceiling assembly with a minimum fire resistance a 1-hr as defined in NFPA 33 (2018) 5.5. Multiple connected booths (or fume hoods) shall not be considered other operations. One or two of the walls of the extraction room structure may be moved into place against a wall of the building provided the building wall carries a fire rating of one hour or greater.

The control panel may be placed on any 40” booth panel located at least 3 feet from the entry door or Utility Penetration Plate. The space within 3 feet of the entry door opening, and the Utility Penetration Plate, is a Class I, Division 2 hazardous location. Only electrical equipment rated for Class I, Division 2 locations can be located within this barrier.

The Extraction Booth is designed for indoor use only. The components are not designed for exposure to weather.

 

CLASS I, DIVISION 2 EXTRACTION FUME HOOD PLACEMENT

The Fume Hood System is assembled from the exterior, so space for the worker is required between the exterior wall of the Fume Hood and walls of the building.

The Fume Hood shall be installed a minimum distance of 3 feet from all operations. The Fume Hood can be installed within 3 feet from all operations if it is separated by a partition, wall, or floor/ceiling assembly with a minimum fire resistance a 1-hr as defined in NFPA 33 (2018) 5.5. Multiple connected booths (or fume hoods) shall not be considered other operations. One or two of the walls of the fume hood structure may be moved into place against a wall of the building provided the building wall carries a fire rating of one hour or greater.

The control panel may be placed anywhere beyond 3 feet from the door or Utility Penetration Plates. The space within 3 feet of the door opening, and the Utility Penetration Plate, is a Class I, Division 2 hazardous location. Only electrical equipment rated for Class I, Division 2 locations can be located within this barrier.

The HAL Extraction Fume Hood is designed for indoor use only. The components are not designed for exposure to weather.

SHIPPING AND RECEIPT

HAL Extraction Booths and Fume Hoods are shipped in one or two crates, depending on the size of the unit.

A forklift is required for unloading of the crate(s) at delivery. HAL Extraction can also coordinate Call-Before-Delivery service along with your freight delivery.

Electrical

Conduit between the Control Panel and individual components is not supplied. Conduit inside the Extraction Booth and Fume Hood Systems, and within 3 feet of the door and Utility Penetration Plate must be rated for used in hazardous locations.
Licensed electrician services, including connection to building power supply, and assembly are not included in the HAL Extraction Booth or Fume Hood, unless specifically stated.
A single-phase 208VAC circuit is all that is needed to power the Extraction Booth or Fume Hood System (including all of its components).
A licensed electrician is required to complete the installation of each Extraction Booth or Fume Hood System.

MECHANICAL

Customers are encouraged to use the services of a mechanical engineer to design the air supply and exhaust ducting, as well as equipment suitable for the installation. A mechanical contractor will be required to install exhaust ducting on the Extraction Booth or Fume Hood System, make roof penetrations, and install roof caps. (note: the Fume Hood System requires no supply side ventilation ducting.
Mechanical contractor services, including installation and supply of duct-work, is not included in the Extraction Booth or Fume Hood, unless specifically stated.
The HVAC system installed on the Extraction Booth or Fume Hood, should be capable of supplying and exhausting the minimum air flow rates, noted on each model's cut sheet and installation manual. Typically, only the base flow rate air is heated or cooled, if at all.

FIRE SUPPRESSION

Fire suppression systems are not included in the retail price of the HAL Extraction Booth or Fume Hood. A standalone powder fire suppression system is available for all booth models and can easily be integrated into your Extraction Booth or Fume Hood.
If your space already has a water based sprinkler system, it is often more cost-effective to tap into that system for your Extraction Booth or Fume Hood.

EXTRACTION BOOTH MODELS

The HAL Extraction Booth is a turn-key Modular CI/D1 Extraction Solution for hydrocarbon and Class IB flammable solvents.

Our patent pending technology has been designed to provide the easiest and safest solution for extraction using flammable solvents.

EXTRACTION FUME HOOD MODELS

The HAL Extraction Fume Hood is a turn-key Modular CI/D2 Primary and Post-Extraction Solution for a variety of flammable solvents.

Our patent pending technology has been designed to provide the easiest and safest solution for extraction using flammable solvents.

Contact our Extraction Booth Team

Learn more about our affordable extraction rooms, booths, and fume hoods, and how you can get your production facility up and running.

Come see us and our friends @pinnaclestainless @extractiontek @ps_inspectors at booth 1114 today!
Come see us and our friends @pinnaclestainless @extractiontek @ps_inspectors at booth 1114 today!
Our booths are all over the map!
Our booths are all over the map!
Can’t wait to see you all @mjbizdaily
Can’t wait to see you all @mjbizdaily
Happy HALloween from our #spookybooth to yours! #ghosts #boo #c1d1 #extraction
Happy HALloween from our #spookybooth to yours! #ghosts #boo #c1d1 #extraction